THE WORLD
OF SCAME

LIBERA Series
Connectors for electric vehicles

BEHIND THE WHEEL OF INNOVATION

• TOTAL SAFETY
• SOFTWARE
• LEGISLATIVE
• CONNECTION DEVELOPED BY SCAME
• CHARGING STATIONS
• CONNECTORS

THERE IS A GREAT EFFORT BEHIND THIS PROJECT

The world changes.

It is inevitable. It is often a steady evolution, but at times sudden changes occur that lead to new scenarios in just a short time.

The introduction of electric vehicles on the market entails the creation of new habits, new structures, and new needs.

In such an evolving context, it is important to establish points of reference that guide the change; in this case, the more qualified, and thus credible, figure becomes the main player.

SCAME did not hesitate for a second to offer a tangible and functional contribution in order to achieve sustainable choices from a technological, economic and environmental standpoint.

A considerable commitment, which SCAME has gladly been devoted to for many years, with the aim of providing tomorrow’s drivers with practical and safe instruments.

WE HAVE FONDED THE ALLIANCE TO BUILD ON GOOD IDEAS

In Europe, there are many technicians with experience and skills, but in order to make the most of this wealth it was necessary to find a way to coordinate the work being carried out, channel choices and share objectives.

SCAME, in conjunction with Legrand and Schneider Electric, founded EV Plug Alliance, an association that aims to ensure compliance of connections used to supply electrical vehicles with CEI standards.

The association’s efforts are geared towards setting up a European standard capable of guaranteeing the highest levels of safety.

CONNECTORS FOR ELECTRIC VEHICLES

CONNECTORS FOR ELECTRIC VEHICLES
REFERENCE STANDARDS

IEC 62196-1 (FDIS)
Plugs, socket-outlets, vehicle couplers and vehicle inlets.
Conductive charging of electric vehicles.
Part 1: General requirements.

IEC 62196-2 (FDIS)
Plugs, socket-outlets and vehicle couplers.
Conductive charging of electric vehicles.
Part 2: Dimensional interchangeability requirements
for a.c. pin and contact-tube accessories.

IEC/EN 61851-1
Electric vehicle conductive charging system.
Part 1: General requirement.

CEI 69-6
Standardization sheet of plug and socket-outlet for the
connection electric road vehicles tot the supply network.

CONNECTORS FOR ELECTRIC VEHICLES
TECHNICAL CHARACTERISTICS

Nominal current:
16A single-phase (type 3A)
16-32A single/three-phase (type 3C)
Nominal voltage:
0-30V (signal)
-12/+12VDC (block)
200-250VAC (single-phase)
380-480VAC (three-phase)
Frequency: 50-60Hz
Insulating voltage: 250V (type 3A) – 500V (type 3C)
Degree of protection:
IP44
IPXXD (type 3A socket, type 3C plug and socket not connected)
Operating temperature: -30°C +50°C
Minimum temperature: -35°C
Maximum temperature: +60°C
Glow Wire test / UL94:
850°C/V1 (type 3A)
850°C-960°C/V1-V0 (type 3C)
Material: Technopolymer
IK degree at 20°C: IK07 (type 3A) – IK08 (type 3C)
Number of poles:
L1-N-E-CP (type 3A)
L1-L2-L3-N-E-CP-PP (type 3C)
Saline solution: Resistant
UV rays: Resistant

CHARGING STATIONS

CHARGING STATIONS
REFERENCE STANDARDS

IEC 62196-1 (FDIS)
Plugs, socket-outlets, vehicle couplers and vehicle inlets.
Conductive charging of electric vehicles.
Part 1: General requirements.

IEC 62196-2 (FDIS)
Plugs, socket-outlets and vehicle couplers.
Conductive charging of electric vehicles.
Part 2: Dimensional interchangeability requirements
for a. c. pin and contact-tube accessories.

IEC/EN 61851-1
Electric vehicle conductive charging system.
Part 1: General requirement.

CEI 312-1
Safety prescriptions for charging stations for
electric road vehicles.

CHARGING STATIONS
TECHNICAL CHARACTERISTICS

Nominal current:
16/32A (consumer units)
32/63A (columns)
Nominal voltage:
0-30V (signal)
+12/-12VDC (block)
200-250VAC (single-phase)
380-480VAC (three-phase)
Frequency: 50-60Hz
Insulation voltage: 500V
Degree of protection:
IP44
IPXXD (socket not connected)
Operating temperature: -30°C +50°C
Minimum temperature: -35°C
Maximum temperature: +60°C
Glow Wire test: 650°C (consumer units)
Material:
- Technopolymer
- Steel sheet
- Steel AISI304
IK degree at 20°C:
IK07 (consumer units)
IK08 (columns)
Completely insulated: Yes
Assembly:
- Wall
- Pole
- Base
Colour: Grey
Saline solution: Resistant
UV rays: Resistant