THE WORLD
OF SCAME

ADVANCE2 Series
Switched interlocked socket outlets (surface mounting)

GENERAL DESCRIPTION

SCAME, ADVANCE 2 Series, interlocked socket outlets have smooth and well-connected surfaces, with no sharp edge or lines, included the hand grip, which ensure top safety and ergonomic use as well as easy cleaning, being installed in environments that particularly need such requirement.

A vertical convex strip symmetrically runs along the front side, gathering the handgrip control, which can be also provided with lock, the transparent opening for the monitoring of switches or protective fuses that connect down with the socket, following the round profile of the cover and being a sort of functional axis of the product.

The small window has been installed by overprinting.

It allows maintaining the IP67 degree of protection without using any gasket or shutter, with perfectly smooth surfaces.

TECHNICAL CHARACTERISTICS

Protection degree: IP44 – IP67 Threaded cable inlet with possible in-out device on the bottom. Complete interchangeability with the installed product. Grip can be locked. Screwless plate. Plate with overprinted window. Seals made by co-printing and skimming. Use of socket plugs with rubber gaskets. Reduced number of versions in two dimensions only. A complete range of products for manifold planning and installing solutions. Up to 6 modules that can be installed in the versions with DIN slide. Improved mechanical interlocking system. Very few elements to be assembled for easy and quick installing and maintaining operations. Provided with ground clamp firmly anchored to the base. Wide room for cabling.

ADVANCE 2 Series:
Wall socket with mechanical lock.

Compatible with ADVANCE System

VERSIONS >50V
(METRIC CABLE INLET)

- Compact version 16A & 32A

1 M25 threaded on upper side
2 marks for M20 on lower side
1 back mark
Provided with large version M25

- Large version 16A & 32A

1 M25 threaded on upper side
2 marks for M20 on lower side
1 back mark
Provided with cable gland M25

- 63A large version

1 M40 threaded on upper side
2 marks for M32 on lower side
1 back mark
Provided with cable gland M40

VERSIONS <50V

• With SELV transformer
• With DIN rail, without SELV transformer

Both the versions are available in HD material be fitted into the ADVANCE System.

THE EXTRA-LOW VOLTAGE SYSTEM OF SAFETY (SELV)

		Primary circuit
		Transformer
		Secondary circuit
ADVANCE 2 Series < 50V Protections for the version with transformer

The SELV system is effectively used on low voltage installations to provide protection against shock hazards for personnel in the event of direct or indirect contacts.
IEC 60364 Standards require the following essential conditions to be met by an installation to implement the SELV system:

- rated voltage: not above 50V~ or 120V d.c.
- power supply: from a safety source with galvanic separation, eg. safety transformer, emergency generator, battery, equivalent electronic devices, etc.
- live parts are not earthed nor connected to the live parts of other electrical systems nor to protective conductors of other circuits
- electric circuits: electric separation from other circuits with isolation characteristics equal to those provided between the primary and secondary winding of the safety transformers, use a nonmetallic sheath.
- metallic bodies should not be earthed nor connected to protective conductors or the metallic bodies of other electrical systems nor to external metallic bodies
- plugs should not be inserted into the sockets of other electrical systems
- sockets should not allow for the insertion of plugs of other electrical systems and should not have earth contact.

CHARACTERISTICS OF THE HD MATERIAL

This designation refers to a series of SCAME products made of special polymer alloys, the result of lengthy research and testing both in the laboratory and in the field.

The materials used have excellent resistance to ambient conditions such as humidity, steam, saline or acid fumes.

The performance of the products is therefore unaffected and remains unchanged over time.

CHARACTERISTICS OF THE HD MATERIAL

The chemical and physical characteristics of the material used for HEAVY DUTY boxes are listed as well as relevant reference standards and the chemical compounds they guarantee protection from.

Excellent stability to the following chemical compounds:

Acids: 10% hydrochloric acid, 30% sulphuric acid, 10% acetic acid.
Alkaline: 10% sodium hydroxide (caustic soda), 10% potassium hydroxide.
Organic solvents: ethyl alcohol, isopropyl alcohol, ethylene glycol.
Oils and fuels for motor-vehicles: engine, brake, gear oil; 2-star petrol, 4-star petrol, leadfree petrol.
Salts: 5% sodium chloride, 10% zinc chloride, 10% calcium chloride.

The following compounds should be avoided:
Organic solvents: acetone, methylene chloride, ethyl acetate.
Alkaline: 10% ammonium hydroxide.